Moteur de recherche de fiches techniques de composants électroniques
  French  ▼

Delete All


Preview PDF Download HTML

E-1048-S700DC24V-1.0A Fiches technique(PDF) 1 Page - ETAL Group

No de pièce E-1048-S700DC24V-1.0A
Description  Optimum load protection because a range of current ratings is available
Download  4 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  ETAL [ETAL Group]
Site Internet
Logo ETAL - ETAL Group

E-1048-S700DC24V-1.0A Fiches technique(HTML) 1 Page - ETAL Group

  E-1048-S700DC24V-1.0A Datasheet HTML 1Page - ETAL Group E-1048-S700DC24V-1.0A Datasheet HTML 2Page - ETAL Group E-1048-S700DC24V-1.0A Datasheet HTML 3Page - ETAL Group E-1048-S700DC24V-1.0A Datasheet HTML 4Page - ETAL Group  
Zoom Inzoom in Zoom Outzoom out
 1 / 4 page
background image
Solid state remote power controller E-1048-S7...
Technical data (Tamb = 25 °C, at UN)
Order numbering code
Load circuit
Operating voltage UB
DC 24 V (18...32 V)
Current ratings IN
1; 2; 4; 5 A
Quiescent current IS
typically 0.5 mA
Min. load current
wire break “OFF” condition: Rload > 500 KΩ
Option: wire break in “OFF” and “ON” condition:
wire break “OFF” condition: Rload > typically 500 kΩ
wire break “ON” condition: Iload < typically 130 mA (1 A unit)
Iload < typically 500 mA (2/4/5 A unit)
Voltage drop UDSmax
0.1 V
Trip times tON/tOFF
typically 5 ms / 1.5 ms
Overload disconnection
1.5 (±-0.3) x IN after approx. 200 ms
Short circuit current
max. 50 A L/R = 2- 3 ms
max. 180 A L/R = 0 ms
OFF delay
typically 200 ms
Control input IN+
Control level
between IN+ and GND
Voltage controlled
DC 0 V < low level < 5 V
Input UE
DC 8.5 V < high level < 32 V
Input current IE
1...10 mA (8.5 V...32 V)
Max. switching frequency fmax 100 Hz
Error signal output
Relay contact
max. DC 30 V / 0.5 A
(potential-free signal contact)
min. DC 10 V / 10 mA
General data
Housing material
Operating temperature 0…60°C
Storage temperature
Blade terminals
6.3 mm to EN 60934-6.3-0.8
96 hours at 95% RH, 40 °C
to IEC 60068-2-78,-Cab
climate class 3K3 to EN60721
3g test to IEC 60068-2-6, test Fc
30 g/11 ms halfsine to EN60068-2-7
Protection class
housing IP30 DIN40050
terminals IP00 EN 40050
EMC requirements
noise emission: EN 61000-6-3
noise immunity: EN 61000-6-2
Insulation resistance
>100MΩ (DC500V) auxiliary contact
LINE, LOAD, GND and IN+ (bridged)
Dielectric strength
test voltage AC 500 V, auxiliary con-
tact to LINE, LOAD, GND and IN+
Dimensions (w x h d)
12.5 x 70 x 60 mm
approx. 33g
Type No.
solid state remote power controller for PLC outputs
S700 with wire break monitoring in OFF condition (standard)
S702 with permanent wire break monitoring
S703 without wire break monitoring
Rated voltage
DC 24 V DC 24 V (standard)
Current ratings
1.0 A
2.0 A
4.0 A
5.0 A
E-1048 -
S700 DC 24 V 1.0 A
ordering example
The E-T-A solid state remote power controller for PLC outputs
E-1084-S7... is a transistor switch with integral protection and
signalling functions. It is used in applications where the existing
PLC output power is not sufficient. In addition the device provides
protection against short circuit and overload as well as a monitoring
function with regard to wire break. The solid state remote power
controller E-1048-S7.. reduces the number of components such as fuses
and relays and avoids the use of expensive powerful output cards.
The devices are operated on a power distribution module 17plus
and they also fit into the smart power distribution system SVS16.
The E-1048-S7.. easily allows control, protection and load circuit
diagnosis and offers reduced wiring efforts.
Automation and process control
- Coupler component for cost-effective power gain at PLC outputs
- Optimum protection of every single load by load circuit monitoring
Protection and control for fast switching operations with:
- motors
- magnetic valves
- resistive loads
- signalling and monitoring lamps
Optimum load protection because a range of current ratings is
No derating over the entire temperature range
Fast short circuit disconnection with simultaneous short-circuit
Time-dependent overload disconnection (trip curve similar to
thermal-magnetic circuit breakers)
Remotely controllable
Error message: LED and signal output indicate overload/short
circuit and wire break in the “OFF” condition (version 700), wire
break in “OFF” and “ON” condition: (type: 702)
Physically isolated fault indication
Compact enclosure
Plug-in design to fit into power distribution module 17plus and
power distribution system SVS16

Html Pages

1  2  3  4 

Fiches technique Télécharger

Go To PDF Page

Lien URL

Politique de confidentialité
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©

Mirror Sites
English :  |   English :  |   Chinese :  |   German :  |   Japanese :
Russian :  |   Korean :  |   Spanish :  |   French :  |   Italian :
Portuguese :  |   Polish :  |   Vietnamese :