Moteur de recherche de fiches techniques de composants électroniques
  French  ▼
ALLDATASHEET.FR

X  

6--22278--5 Fiches technique(PDF) 3 Page - Tyco Electronics

No de pièce 6--22278--5
Description  Feed- Through Head Assembly
Download  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  MACOM [Tyco Electronics]
Site Internet  http://www.macom.com
Logo MACOM - Tyco Electronics

6--22278--5 Fiches technique(HTML) 3 Page - Tyco Electronics

  6--22278--5 Datasheet HTML 1Page - Tyco Electronics 6--22278--5 Datasheet HTML 2Page - Tyco Electronics 6--22278--5 Datasheet HTML 3Page - Tyco Electronics 6--22278--5 Datasheet HTML 4Page - Tyco Electronics 6--22278--5 Datasheet HTML 5Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 3 / 5 page
background image
408- 9607
Feed- Through Head Assembly 58443- 1
3
of 5
Rev C
Tyco Electronics Corporation
the direction of the arrow) until it stops, then
release the trigger or foot pedal (the receptacle
should advance so that the first contact aligns with
the wire inserter).
4. Check that the locating pawl is resting between
the index ribs of the receptacle. See Figure 2. If
not, push the receptacle out of the RIGHT side of
the head, and re--insert it.
After making the test crimp, the wire
sub--assembly retainer can be used (as shown in
Figure 2) to hold and locate the wires during
terminations. Pivot the retainer latch to open the
retainer.
5. Insert an unstripped wire into the funnel area
between the contact and the wire inserter until it is
in the desired location to be terminated.
6. Actuate the tool according to the instructions
included with the tool. When the cycle is
completed, the wire inserter will retract, and the
feed slide will automatically advance the receptacle
to the next contact position.
The locating pawl will move up and down as the
receptacle is automatically advanced through the
head. However, if movement is obstructed, or if
desired, depress the locating pawl and push the
receptacle out of the RIGHT side of the head.
7. Repeat Steps 4 through 6 until all contacts have
been terminated.
8. Inspect each termination according to Section 5.
5. TERMINATION INSPECTION
Refer to Figure 3, and inspect each termination to
ensure the following:
— the wire is terminated past the lead--in transition
and is about halfway in the contact slot
— the wireis from 2.29to2.74mm [.090 to
.108 in.] beyond the front of the contact beam
— the wire is NOT bottomed in the contact slot
— the contact beams are NOT deformed (if
damage is apparent, replace the contacts in
accordance with the instructions packaged with the
receptacle)
— the wire is NOT nicked or cut in any area other
than the contact slot
— the wires extend beyond the strain--reliefs of the
receptacle
Refer to 114--1020 for detailed application
requirements.
Figure 3
Inspection of Properly Terminated Wire
Cut in Wire
Deformation
Correct
Front of
Contact Beam
Contact
Slot
Lead--In
Transition
Incorrect
Wire
Strain Relief
Figure 4
Rod Inserter
Adjuster
Turn Counterclockwise to Increase
Wire Insertion Depth
Turn Clockwise to Decrease
Wire Insertion Depth
Wire Insertion Depth Adjustment
6. MAINTENANCE AND INSPECTION
The following procedures have been established to
ensure the quality and reliability of the head. The
head should be checked daily, and a more detailed
inspection should be performed by your quality control
group on a regular basis.
6.1. Daily Maintenance
Each operator should be aware of, and responsible
for, the following steps of maintenance.
NOTE
i
NOTE
i
NOTE
i


Numéro de pièce similaire - 6--22278--5

FabricantNo de pièceFiches techniqueDescription
logo
TE Connectivity Ltd
6--21030--8 TEC-6--21030--8 Datasheet
85Kb / 2P
   Adapter Kits for GREENERD Manual
logo
Tyco Electronics
6--23629--0 MACOM-6--23629--0 Datasheet
273Kb / 5P
   Pneumatic Head Assembly
More results

Description similaire - 6--22278--5

FabricantNo de pièceFiches techniqueDescription
logo
Glenair, Inc.
227-03910 GLENAIR-227-03910 Datasheet
427Kb / 2P
   Bulkhead Feed-Through
logo
Eaton All Rights Reserv...
C220X EATON-C220X Datasheet
423Kb / 2P
   Feed through connector
October 2022
logo
Harwin Plc
W2222-00 HARWIN-W2222-00 Datasheet
151Kb / 1P
   FEED THROUGH INSULATOR
logo
Weidmuller
1036180000 WEIDMULLER-1036180000 Datasheet
100Kb / 3P
   Modular feed-through terminals
0337100000 WEIDMULLER-0337100000 Datasheet
66Kb / 1P
   Modular feed-through terminals
1036100000 WEIDMULLER-1036100000 Datasheet
96Kb / 3P
   Modular feed-through terminals
logo
Tyco Electronics
408-4070 MACOM-408-4070 Datasheet
273Kb / 5P
   Pneumatic Head Assembly
logo
Cooper Bussmann, Inc.
C7021-02N-1 COOPER-C7021-02N-1 Datasheet
94Kb / 1P
   Power Feed Through Terminal Blocks
logo
PHOENIX CONTACT
3100305 PHOENIX-3100305 Datasheet
131Kb / 5P
   Feed-through modular terminal block
logo
Rosenberger Hochfrequen...
51Z101-006A ROSENBERGER-51Z101-006A Datasheet
40Kb / 2P
   BNC 50 CABLE FEED THROUGH
More results


Html Pages

1 2 3 4 5


Fiches technique Télécharger

Go To PDF Page


Lien URL




Politique de confidentialité
ALLDATASHEET.FR
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com