Moteur de recherche de fiches techniques de composants électroniques
  French  ▼
ALLDATASHEET.FR

X  

LM2642 Fiches technique(PDF) 3 Page - Texas Instruments

Click here to check the latest version.
No de pièce LM2642
Description  Two-Phase Synchronous Step-Down Switching Controller
Download  31 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  TI1 [Texas Instruments]
Site Internet  http://www.ti.com
Logo TI1 - Texas Instruments

LM2642 Fiches technique(HTML) 3 Page - Texas Instruments

  LM2642 Datasheet HTML 1Page - Texas Instruments LM2642 Datasheet HTML 2Page - Texas Instruments LM2642 Datasheet HTML 3Page - Texas Instruments LM2642 Datasheet HTML 4Page - Texas Instruments LM2642 Datasheet HTML 5Page - Texas Instruments LM2642 Datasheet HTML 6Page - Texas Instruments LM2642 Datasheet HTML 7Page - Texas Instruments LM2642 Datasheet HTML 8Page - Texas Instruments LM2642 Datasheet HTML 9Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 31 page
background image
LM2642
www.ti.com
SNVS203I – MAY 2002 – REVISED APRIL 2013
system.
ON/SS1 (Pin 9) Channel 1 enable pin. This pin is internally pulled up to one diode drop above VLIN5. Pulling
this pin below 1.2V (open-collector type) turns off Channel 1. If both ON/SS1 and ON/SS2 pins are pulled
below 1.2V, the whole chip goes into shut down mode. Adding a capacitor to this pin provides a soft-start
feature that minimizes inrush current and output voltage overshoot.
ON/SS2 (Pin 10) Channel 2 enable pin. See the description for Pin 9, ON/SS1. May be connected to ON/SS1 for
simultaneous startup or for parallel operation.
FB2 (Pin 11) Feedback input for channel 2. Connect to VOUT through a voltage divider to set the Channel 2
output voltage.
COMP2 (Pin 12) Compensation pin for Channel 2. This is the output of the internal transconductance amplifier.
The compensation network should be connected between this pin and the signal ground SGND (Pin 8).
ILIM2 (Pin 13) Current limit threshold setting for Channel 2. See ILIM1 (Pin 2).
KS2 (Pin 14) The positive (+) Kelvin sense for the internal current sense amplifier of Channel 2. See KS1 (Pin 1).
RSNS2 (Pin 15) The negative (-) Kelvin sense for the internal current sense amplifier of Channel 2. Connect this
pin to the low side of the current sense resistor that is placed between VIN and the drain of the top
MOSFET. When the Rds of the top MOSFET is used for current sensing, connect this pin to the source of
the top MOSFET. Always use a separate trace to form a Kelvin connection to this pin.
SW2 (Pin 16) Switch-node connection for Channel 2, which is connected to the source of the top MOSFET of
Channel 2. It serves as the negative supply rail for the top-side gate driver, HDRV2.
HDRV2 (Pin 17) Top-side gate-drive output for Channel 2. HDRV is a floating drive output that rides on the
corresponding switching-node voltage.
CBOOT2 (Pin 18) Bootstrap capacitor connection. It serves as the positive supply rail for the Channel 2 top-side
gate drive. Connect this pin to VDD2 (Pin 19) through a diode, and connect the low side of the bootstrap
capacitor to SW2 (Pin16).
VDD2 (Pin 19) The supply rail for the Channel 2 low-side gate drive. Connected to VLIN5 (Pin 7) through a 4.7
resistor and bypassed to power ground with a ceramic capacitor of at least 1µF. Tie this pin to VDD1 (Pin
24).
LDRV2 (Pin 20) Low-side gate-drive output for Channel 2.
PGND (Pin 21) The power ground connection for both channels. Connect to the ground rail of the system.
VIN (Pin 22) The power input pin for the chip. Connect to the positive (+) input rail of the system. This pin must
be connected to the same voltage rail as the top FET drain (or the current sense resistor when used).
LDRV1 (Pin 23) Low-side gate-drive output for Channel 1.
VDD1 (Pin 24) The supply rail for Channel 1 low-side gate drive. Tie this pin to VDD2 (Pin 19).
CBOOT1 (Pin 25) Bootstrap capacitor connection. It serves as the positive supply rail for Channel 1 top-side gate
drive. See CBOOT2 (Pin 18).
HDRV1 (Pin 26) Top-side gate-drive output for Channel 1. See HDRV2 (Pin 17).
SW1 (Pin 27) Switch-node connection for Channel 1. See SW2 (Pin16).
RSNS1 (Pin 28) The negative (-) Kelvin sense for the internal current sense amplifier of Channel 1. See RSNS2
(Pin 15).
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM2642


Numéro de pièce similaire - LM2642

FabricantNo de pièceFiches techniqueDescription
logo
National Semiconductor ...
LM2642 NSC-LM2642 Datasheet
643Kb / 20P
   Two-Phase Synchronous Step-Down Switching Controller
logo
Texas Instruments
LM2642 TI-LM2642 Datasheet
1Mb / 31P
[Old version datasheet]   LM2642 Two-Phase Synchronous Step-Down Switching Controller
logo
National Semiconductor ...
LM26420 NSC-LM26420 Datasheet
635Kb / 28P
   Dual 2.0A, High Frequency Synchronous Step-Down DC-DC Regulator
logo
Texas Instruments
LM26420 TI1-LM26420 Datasheet
1Mb / 47P
[Old version datasheet]   Dual 2-A Automotive-Qualified, High-Efficiency Synchronous DC-DC Converter
LM26420-Q0 TI-LM26420-Q0 Datasheet
1Mb / 44P
[Old version datasheet]   LM26420/LM26420-Q0/Q1 Dual 2-A Automotive-Qualified, High-Efficiency Synchronous DC-DC Converter
More results

Description similaire - LM2642

FabricantNo de pièceFiches techniqueDescription
logo
National Semiconductor ...
LM2642 NSC-LM2642 Datasheet
643Kb / 20P
   Two-Phase Synchronous Step-Down Switching Controller
logo
Texas Instruments
LM2642MTCX TI-LM2642MTCX Datasheet
1Mb / 31P
[Old version datasheet]   LM2642 Two-Phase Synchronous Step-Down Switching Controller
logo
National Semiconductor ...
LM2648 NSC-LM2648 Datasheet
1,017Kb / 23P
   Two-Phase, Synchronous Step-Down 3-Channel Switching Regulator Controller
logo
Linear Technology
LTC3850 LINER-LTC3850_15 Datasheet
595Kb / 38P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
LTC3850-2 LINER-LTC3850-2 Datasheet
401Kb / 36P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
LTC3850 LINER-LTC3850 Datasheet
522Kb / 36P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
LTC3850-2 LINER-LTC3850-2_15 Datasheet
413Kb / 36P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
LTC3850EUFDTRPBF LINER-LTC3850EUFDTRPBF Datasheet
595Kb / 38P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
LTC3850-1 LINER-LTC3850-1_15 Datasheet
595Kb / 38P
   Dual, 2-Phase Synchronous Step-Down Switching Controller
logo
Semtech Corporation
SC2443 SEMTECH-SC2443_08 Datasheet
1Mb / 22P
   Dual-Phase Single or Two Output Synchronous Step-Down Controller
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31


Fiches technique Télécharger

Go To PDF Page


Lien URL




Politique de confidentialité
ALLDATASHEET.FR
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com