Moteur de recherche de fiches techniques de composants électroniques |
|
CBC2016T100KR Fiches technique(PDF) 11 Page - Taiyo Yuden (U.S.A.), Inc |
|
CBC2016T100KR Fiches technique(HTML) 11 Page - Taiyo Yuden (U.S.A.), Inc |
11 / 11 page 12 wound0103_reli-PRP6 wound0103_reli_e-01 ■ PRECAUTIONS *This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 1.Circuit Design Precautions ◆Operating environment 1.The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2.PCB Design Precautions ◆Land pattern design 1.Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. Technical consider- ations PRECAUTIONS 【Recommended Land Patterns】 Surface Mounting ・Mounting and soldering conditions should be checked beforehand. ・Applicable soldering process to those products is reflow soldering only. 3.Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical consider- ations 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4.Soldering Precautions ◆Wave soldering(LEM Type only) 1.For wave soldering,please apply conditions meeting the range of the specifed conditions in our catalog or the relevant specifications. ◆Reflow soldering(LB and CB Types) 1.For reflow soldering with either leaded or lead-free solder,the profile specified in "point for controlling" is recommended. ◆Reflow soldering(LEM) 1.For reflow soldering, please apply conditions meeting the range of the specified conditions in our catalog or the relevant specifications. ◆Recommended conditions for using a soldering iron 1.Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron shoud not come in contact with inductor directly. Technical consider- ations ◆Wave soldering(LEM Type only) 1.Components can be damaged by excessive heat where soldering conditions exceed the specified range. ◆Reflow soldering(LB and CB Types) 1.Reflow profile 300 250 200 150 100 50 0 Pre-heat zone 90±30 sec 30±10 sec 230℃ Minn Peak Temp: 260+0/ー5℃ 5 sec Max 180℃ 150℃ ◆Recommended conditions for using a soldering iron 1.Components can be damaged by excessive heat where soldering conditions exceed the specified range. 5.Cleaning Precautions ◆Cleaning conditions Washing by supersonic waves shall be avoided. Technical consider- ations ◆Cleaning conditions If washed by supersonic waves, the products might be broken. 6.Handling Precautions ◆Handling 1.There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards(splitting along perforations) 1.Planning pattern configurations and the position of products should be carefully performed to minimize stress. ◆Mechanical considerations 1.There is a case to be damaged by a mechanical shock. Technical consider- ations ◆Handling 1.Keep the inductors away from all magnets and magnetic objects. ◆Breakaway PC boards(splitting along perforations) 1.When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2.Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations 1.Please do not give the inductors any excessive mechanical shocks. 7.Storage conditions Precautions ◆Storage 1.Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. Technical consider- ations ◆Storage 1.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・Recommended conditions Ambient temperature:0~40℃ / Humidity:Below 70% RH The ambient temperature must be kept below 30℃ even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, LE type inductors should be used within one year from the time of delivery. LB type:Should be used within 6 months from the time of delivery. LE type:In case of storage over 6 months, solderability shall be checked before actual usage. LEM Type,LB Type,CB Type |
Numéro de pièce similaire - CBC2016T100KR |
|
Description similaire - CBC2016T100KR |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |