Moteur de recherche de fiches techniques de composants électroniques
  French  ▼

Delete All
ON OFF
ALLDATASHEET.FR

X  

Preview PDF Download HTML

US1205 Fiches technique(PDF) 3 Page - UNISEM

No de pièce US1205
Description  300 mA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR
Download  3 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  UNISEM [UNISEM]
Site Internet  
Logo UNISEM - UNISEM

US1205 Fiches technique(HTML) 3 Page - UNISEM

  US1205 Datasheet HTML 1Page - UNISEM US1205 Datasheet HTML 2Page - UNISEM US1205 Datasheet HTML 3Page - UNISEM  
Zoom Inzoom in Zoom Outzoom out
 3 / 3 page
background image
US1205
2-3
Rev. 1.4
9/25/00
PIN #
PIN SYMBOL
PIN DESCRIPTION
A resistor divider from this pin to the Vout pin and ground sets
the output voltage.
A 470 to 1000pF bypass capacitor connected to this pin re-
duces the output noise.
The output of the regulator .A minimum of 2.2uF with max
ESR of 1 ohm capacitor must be connected from this pin to
ground to insure stability.
Ground pin. This pin must be connected to the lowest poten-
tial in the system & all other pins must be at higher potential
with respect to this pin.
Enable pin. A low signal or left open on this pin shuts down the
output.This pin must be tied HI or to Vin for normal operation.
The input pin of the regulator. Typically a large storage capacitor
is connected from this pin to ground to insure that the input
voltage does not sag below the minimumdrop out voltage dur-
ing the load transient response. This pin must always be higher
than Vout by at least the amount of the dropout voltage and
some margin in order for the device to regulate properly.
4
Adj
(Adjustable only)
4
Byp
(Fixed output only)
5
Vout
2
GND
3
En
1
Vin
5 LEAD
Output
SOT 23
Voltage
US1205
1.242V
US1205-25
2.5 V
US1205-30
3.0 V
US1205-33
3.3 V
US1205-36
3.6 V
Table 1- Nominal output voltage v.s. part number
BLOCK DIAGRAM
BLOCK DIAGRAM
Note 3 : Ground current is the the regulator quiescent
current plus the pass transistor current. The total cur-
rent from the supply is the sum of the load current plus
the ground pin current.
Note 4 : The specification applies for the junction tem-
perature of 0 to +125
°C.
Note 1 : Low duty cycle pulse testing with Kelvin con-
nections are required in order to maintain accurate data.
Note 2 : Drop-out voltage is defined as the minimum
differential voltage between Vin and Vout required to main-
tain regulation at Vout. It is measured when the output
voltage drops 1% below its nominal value.
Vin
En
1205blk1-1.1
+
THERMAL
SHUTDOWN
1.242V
Vout
Adj
Gnd
Vin
En
1205blk2-1.0
+
THERMAL
SHUTDOWN
1.242V
Vout
Byp
Gnd
Figure 1- US1205 Adjustable block diagram
Figure 2- US1205 Fixed output block diagram
Pin DescRIPTIONS
Pin DescRIPTIONS
The output voltage of the adjustable device can be set using:
Vo=1.242 X (1+R1/R2)
Where;
R1=Resistor connected from output to the Adj pin
R2=Resistor connected from Adj pin to GND


Html Pages

1  2  3 


Fiches technique Télécharger

Go To PDF Page


Lien URL




Politique de confidentialité
ALLDATASHEET.FR
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn