Moteur de recherche de fiches techniques de composants électroniques |
|
TS2GCF100I Fiches technique(PDF) 7 Page - Transcend Information. Inc. |
|
TS2GCF100I Fiches technique(HTML) 7 Page - Transcend Information. Inc. |
7 / 80 page T T Trrra a an n ns s sc c ce e en n nd d d IIIn n nd d du u us s stttrrriiia a alll C C CF F F C C Ca a arrrd d d (((T T TS S S1 1 12 2 28 8 8M M M ~ ~ ~ 1 1 16 6 6G G GC C CF F F1 1 10 0 00 0 0III))) Transcend Information Inc. V1.2 7 Signal Description Signal Name Dir. Pin Description A10 – A00 (PC Card Memory Mode) A10 – A00 (PC Card I/O Mode) A02 - A00 (True IDE Mode) I I 8,10,11,12, 14,15,16,17, 18,19,20 18,19,20 These address lines along with the -REG signal are used to select the following: The I/O port address registers within the CompactFlash Storage Card , the memory mapped port address registers within the CompactFlash Storage Card, a byte in the card's information structure and its configuration control and status registers. This signal is the same as the PC Card Memory Mode signal. In True IDE Mode, only A[02:00] are used to select the one of eight registers in the Task File, the remaining address lines should be grounded by the host. BVD1 (PC Card Memory Mode) -STSCHG (PC Card I/O Mode) Status Changed -PDIAG (True IDE Mode) I/O 46 This signal is asserted high, as BVD1 is not supported. This signal is asserted low to alert the host to changes in the READY and Write Protect states, while the I/O interface is configured. Its use is controlled by the Card Config and Status Register. In the True IDE Mode, this input / output is the Pass Diagnostic signal in the Master / Slave handshake protocol. BVD2 (PC Card Memory Mode) -SPKR (PC Card I/O Mode) -DASP (True IDE Mode) I/O 45 This signal is asserted high, as BVD2 is not supported. This line is the Binary Audio output from the card. If the Card does not support the Binary Audio function, this line should be held negated. In the True IDE Mode, this input/output is the Disk Active/Slave Present signal in the Master/Slave handshake protocol. -CD1, -CD2 (PC Card Memory Mode) -CD1, -CD2 (PC Card I/O Mode) -CD1, -CD2 (True IDE Mode) O 26,25 These Card Detect pins are connected to ground on the CompactFlash Storage Card. They are used by the host to determine that the CompactFlash Storage Card is fully inserted into its socket. This signal is the same for all modes. This signal is the same for all modes. |
Numéro de pièce similaire - TS2GCF100I |
|
Description similaire - TS2GCF100I |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |