SPT574

ALTERNATIVE

In some applications, a full scale of 10.24 V (for an LSB of

2.5 mV) or 20.48 V (for an LSB of 5.0 mV) is more convenient.

In the unipolar mode of operation, replace R2 with a 200

Ω

potentiometer and add 150

Ω in series with the 10 V IN pin for

10.24 V input range or 500

Ω in series with the 20 V IN pin for

20.48 V input range. In bipolar mode of operation, replace R1

with a 500

Ω potentiometer (in addition to the previous

changes). The calibration will remain similar to the standard

calibration procedure.

CONTROLLING THE SPT574

The SPT574 can be operated by most microprocessor sys-

tems due to the control input pins and on-chip logic. It may

also be operated in the stand-alone mode and enabled by the

R/C input pin. Full µP control consists of selecting an 8 or

12-bit conversion cycle, initiating the conversion, and reading

the output data when ready. The output read has the options

of choosing either 12-bits at once or 8 bits followed by

4-bits in a left-justified format. All five control inputs are TTL/

The use of these inputs in controlling the converter’s opera-

tions is shown in table I, and the internal control logic is shown

in a simplified schematic in figure 10.

STAND-ALONE OPERATION

The simplest interface is a control line connected to R/

output controls must be tied to known states as follows: CE

cycle are shown in figures 3 and 4. It may have a duty cycle

within and including the extremes shown in the specifica-

STS is also high, indicating a conversion is in progress.

Table I - Truth Table for the SPT574 Control Inputs

CE

Ao

Operation

CS

R/C

12/8

0

XXXX

None

X

1

X

X

X

None

0

0

X

0

Initiate 12 bit conversion

0

0

X

1

Initiate 8 bit conversion

1

0

X

0

Initiate 12 bit conversion

1

0

X

1

Initiate 8 bit conversion

1

0

X

0

Initiate 12 bit conversion

1

0

X

1

Initiate 8 bit conversion

10

1X

1

Enable 12 bit Output

10

00

1

Enable 8 MSB's Only

10

01

1

Enable 4 LSB's Plus 4

Trailing Zeroes

Figure 7 - Interfacing the SPT574 to an 8-Bit Data Bus

Address Bus

Ao

~

Data

Bus

STS

MSB

DIG

COM

LSB

Ao

12/8

CONTROLLED OPERATION

CONVERSION LENGTH

A conversion start transition latches the state of Ao as shown

in figure 7 and table I. The latched state determines if the

conversion stops with 8 bits (Ao high) or continues for 12 bits

(Ao low). If all 12 bits are read following an 8-bit conversion, the

three LSBs will be a logic 0 and DB3 will be a logic 1. Ao is latched

because it is also involved in enabling the output buffers as

will be explained later. No other control inputs are latched.

CONVERSION START

A conversion may be initiated by a logic transition on any of

of the three to reach the correct state starts the conversions,

so one, two or all three may be dynamically controlled. The

nominal delay from each is the same and all three may

change state simultaneously. In order to assure that a par-

ticular input controls the start of conversion, the other two

should be set up at least 50 ns earlier. Refer to the convert

mode timing specifications. The Convert Start timing diagram

is illustrated in figure 1.

The output signal STS is the status flag and goes high only

when a conversion is in progress. While STS is high, the

output buffers remain in a high impedance state so that data

can not be read. Also, when STS is high, an additional Start

Convert will not reset the converter or reinitiate a conversion.

Note, if Ao changes state after a conversion begins, an

additional Start Convert command will latch the new start of

Ao and possibly cause a wrong cycle length for that conver-

sion (8 versus 12 bits).

8

8/1/00