 |
Moteur de recherche de fiches techniques de composants électroniques |
|
|
Moteur de recherche de fiches techniques de composants électroniques |
|
AD1048-24FS Fiches technique(PDF) 2 Page - MicroPower Direct, LLC |
|
||||||||||||||||||||||||||||||
AD1048-24FS Fiches technique(HTML) 2 Page - MicroPower Direct, LLC |
|
|
2 / 2 page  Derating Curve Model Selection Guide Mechanical Dimensions Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Model Number Rated Power (W) Input Output Overvoltage Protection (VDC) Efficiency (%, Typ) Fuse Rating Slow-Blow (A) Voltage (VAC) Current (A) Voltage (VDC) Current (A) Max) Current (A) Range Universal Range 115 VAC 230 VAC AD1036-12FS 36 100 - 240 1.0 0.5 12 3.0 0 ~ 3.0 20.0 80 2.0 AD1045-15FS 45 100 - 240 1.0 0.5 15 3.0 0 ~ 3.0 20.0 81 2.0 AD1048-24FS 48 100 - 240 1.0 0.5 24 2.0 0 ~ 2.0 40.0 83 2.0 AD1048-48FS 48 100 - 240 1.0 0.5 48 1.0 0 ~ 1.0 60.0 83 2.0 Notes: 1. Load regulation is specified for a load change of 20% to 100%. 2. Ripple & noise is measured using equipment with 20 Mhz of bandwidth with the unit under test operating at rated load and a 110 VAC input. Connection to the unit is made with a 0.1 μF / 630V metalized capacitor & a 47 μF electrolytic capacitor connected in parallel. 3. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 4. Isolation resistance is given for Input/Output and Input/FG. For Output/FG., it is 50 M Ω 5. Overload protection is power limiting. The unit recovers automatically when the fault is removed. 6. Over voltage protection is a shut down type. The unit recovers automatically when the fault is removed. 7. To mount the unit to the DIN rail, tilt the unit rearwards from the top, fitting the mount over the top of the rail. Press back on the bottom front of the unit until it locks in place on the rail. To remove the unit from the rail, pull the removal clip at the bottom rear of the unit downward with a screw driver. With the clip down, lift up on the unit from the bottom front until it clears the rail. Before installation or removal all wiring should be disconnected and the main power to the system shut off. 8. When wiring the supply, all lines should be as thick and short as possible. AWG 14 wire is recommended for the AD1048FS series. 9. The units should be mounted so they are vertically orientated. Air flow (if it is provided) would optimally flow from the bottom to the top of the unit. 10. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Terminal Connections Pin Function 1 DC Output (+V) 2 DC Output (-V) 3 Frame Ground (FG) 4 AC/Neutral 5 AC/Live |
Numéro de pièce similaire - AD1048-24FS |
|
Description similaire - AD1048-24FS |
|
|
|
Lien URL |
| Politique de confidentialité |
| ALLDATASHEET.FR |
| ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
French ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
