Moteur de recherche de fiches techniques de composants électroniques
  French  ▼

Delete All


Preview PDF Download HTML

TSOP1530 Fiches technique(PDF) 3 Page - Vishay Siliconix

No de pièce TSOP1530
Description  Photo Modules for PCM Remote Control Systems
Download  7 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  VISHAY [Vishay Siliconix]
Site Internet
Logo VISHAY - Vishay Siliconix

TSOP1530 Fiches technique(HTML) 3 Page - Vishay Siliconix

  TSOP1530 Datasheet HTML 1Page - Vishay Siliconix TSOP1530 Datasheet HTML 2Page - Vishay Siliconix TSOP1530 Datasheet HTML 3Page - Vishay Siliconix TSOP1530 Datasheet HTML 4Page - Vishay Siliconix TSOP1530 Datasheet HTML 5Page - Vishay Siliconix TSOP1530 Datasheet HTML 6Page - Vishay Siliconix TSOP1530 Datasheet HTML 7Page - Vishay Siliconix  
Zoom Inzoom in Zoom Outzoom out
 3 / 7 page
background image
Vishay Telefunken
3 (7)
Rev. 9, 30-Mar 01
Document Number 82029
Suitable Data Format
The circuit of the TSOP15.. is designed in that way that
unexpected output pulses due to noise or disturbance
signals are avoided. A bandpassfilter, an integrator
stage and an automatic gain control are used to
suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fullfill the following condition:
• Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).
• Burst length should be 10 cycles/burst or longer.
• After each burst which is between 10 cycles and 70
cycles a gap time of at least 14 cycles is neccessary.
• For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should be at least 4
times longer than the burst.
• Up to 800 short bursts per second can be received
Some examples for suitable data format are:
NEC Code (repetitive pulse), NEC Code (repetitive
data), Toshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, R–2000 Code.
When a disturbance signal is applied to the TSOP15..
it can still receive the data signal. However the
sensitivity is reduced to that level that no unexpected
pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP15.. are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signal at 38kHz or at any other
• Signals from fluorescent lamps with electronic
ballast with high or low modulation (see Figure A or
Figure B).
time [ms]
Figure A: IR Signal from Fluorescent Lamp with low Modulation
time [s]
Figure B: IR Signal from Fluorescent Lamp with high Modulation

Html Pages

1  2  3  4  5  6  7 

Fiches technique Télécharger

Go To PDF Page

Lien URL

Politique de confidentialité
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©

Mirror Sites
English :  |   English :  |   Chinese :  |   German :  |   Japanese :
Russian :  |   Korean :  |   Spanish :  |   French :  |   Italian :
Portuguese :  |   Polish :  |   Vietnamese :