Moteur de recherche de fiches techniques de composants électroniques |
|
LM258W Fiches technique(PDF) 3 Page - STMicroelectronics |
|
LM258W Fiches technique(HTML) 3 Page - STMicroelectronics |
3 / 18 page LM158W-LM258W-LM358W Absolute maximum ratings and operating conditions 3/18 2 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol Parameter LM158W/AW LM258W/AW LM358W/AW Unit VCC + Supply voltage +32 V Vin Input voltage -0.3 to VCC + +0.3 V Vid Differential input voltage -0.3 to VCC + +0.3 V Output short-circuit duration (1) Infinite Iin Input current (2) 50 mA Toper Operating free-air temperature range -55 to +125 -40 to +105 0 to +70 °C Tstg Storage temperature range -65 to +150 °C Tj Maximum junction temperature 150 °C Rthja Thermal resistance junction to ambient(3) SO-8 MiniSO-8 TSSOP8 DIP-8 125 190 120 85 °C/W Rthjc Thermal resistance junction to case(3) SO-8 MiniSO-8 TSSOP8 DIP-8 40 39 37 41 °C/W ESD HBM: human body model(4) 1.5 kV MM: machine model(5) 200 V CDM: charged device model(6) 1.5 kV 1. Short-circuits from the output to VCC can cause excessive heating if VCC > 15V. The maximum output current is approximately 40 mA independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short- circuits on all amplifiers. 2. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the Op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output will be restored for input voltage higher than -0.3 V. 3. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values. 4. Human body model: 100 pF discharged through a 1.5 k Ω resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 5. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 6. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. |
Numéro de pièce similaire - LM258W |
|
Description similaire - LM258W |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |