Moteur de recherche de fiches techniques de composants électroniques |
|
ADC10464CIWM Fiches technique(PDF) 3 Page - National Semiconductor (TI) |
|
|
ADC10464CIWM Fiches technique(HTML) 3 Page - National Semiconductor (TI) |
3 / 17 page Pin Descriptions Pin Function Description DV CC,AVCC Digital and analog positive supply voltage inputs. Connect both to the same voltage source, but bypass separately with a 0.1 µF ceramic capacitor in parallel with a 10 µF tantalum capacitor to ground at each pin. INT Active low interrupt output. INT goes low at the end of each conversion, and returns high following the rising edge of RD. S/H Sample/Hold control input. When this pin is forced low (and CS is low), the analog input signal is sampled and a new conversion is initiated. RD Active low read control input. When this RD and CS are low, any data present in the output registers will be placed onto the data bus. CS Active low Chip Select control input. When low, this pin enables the RD and S/H pins. S0, S1 On the multiple-input devices (ADC10462 and ADC10464), these pins select the analog input that will be connected to the A/D during the conversion. The input is selected based on the state of S0 and S1 when S/H makes its High-to-Low transition (See the Timing Diagrams). The ADC10464 includes both S0 and S1. The ADC10462 includes just S0, and the ADC10461 has neither. V REF−,VREF+ Reference voltage inputs. They may be placed at any voltage between GND and V CC, but VREF+ must be greater than V REF−. An input voltage equal to VREF− produces an output code of 0, and an input voltage equal to (V REF+ − 1 LSB) produces an output code of 1023. V IN,VIN0,VIN1, V IN2,VIN3 Analog input pins. The ADC10461 has one input (V IN), the ADC10462 has two inputs (VIN0 and V IN1), and the ADC10464 has four inputs (VIN0,VIN1,VIN2 and VIN3). The impedance of the input source should be less than 500 Ω for best accuracy and conversion speed. For accurate conversions, no input pin (even one that is not selected) should be driven more than 50 mV above V CC or 50 mV below ground. GND, AGND, DGND Power supply ground pins. The ADC10461 has a single ground pin (GND), and the ADC10462 and ADC10464 have separate analog and digital ground pins (AGND and DGND) for separate bypassing of the analog and digital supplies. The ground pins should be connected to a stable, noise-free system ground. For the devices with two ground pins, both pins should be returned to the same potential. DB0–DB9 TRI-STATE® data output pins. SPEED ADJ (ADC10462 and ADC10464 only). This pin is normally left unconnected, but by connecting a resistor between this pin and ground, the conversion time can be reduced. See the Typical Performance Curves and the table of Electrical Characteristics. www.national.com 3 |
Numéro de pièce similaire - ADC10464CIWM |
|
Description similaire - ADC10464CIWM |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |