Moteur de recherche de fiches techniques de composants électroniques
  French  ▼

Delete All


Preview PDF Download HTML

STCF01 Fiches technique(PDF) 1 Page - STMicroelectronics

No de pièce STCF01
Description  Step-up Converter for Cell Phone Camera Flash LEDs
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  STMICROELECTRONICS [STMicroelectronics]
Site Internet
Logo STMICROELECTRONICS - STMicroelectronics

STCF01 Fiches technique(HTML) 1 Page - STMicroelectronics

  STCF01 Datasheet HTML 1Page - STMicroelectronics STCF01 Datasheet HTML 2Page - STMicroelectronics STCF01 Datasheet HTML 3Page - STMicroelectronics STCF01 Datasheet HTML 4Page - STMicroelectronics STCF01 Datasheet HTML 5Page - STMicroelectronics STCF01 Datasheet HTML 6Page - STMicroelectronics STCF01 Datasheet HTML 7Page - STMicroelectronics STCF01 Datasheet HTML 8Page - STMicroelectronics STCF01 Datasheet HTML 9Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 1 / 16 page
background image
Preliminary Data
October 2005
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to
change without notice.
Rev. 1
Step-up Converter for Cell Phone Camera Flash LEDs
I Supply voltage range: 2.6V to 5.5V
I 17V Maximum Output Voltage
I Two levels of current up to 300mA set with
external resistors
I Dedicated pin to select the required level of
I Operating frequency: 1.5MHz: PWM Controller
I Torch mode supported
I Shutdown pin with true load disconnection
I Efficiency: 90% at 100mA; 80% at 300mA
I DFN10L (3mm x 3mm) Package
The STCF01 is a dedicated IC designed to drive
two, three, or four white, cell phone camera flash
LEDs with constant current. The step-up (boost)
converter input is connected directly to the battery,
and its converter output voltage is automatically
determined using current feedback-based duty
cycle control.
The STCF01 has a dedicated pin for two levels of
LED current selection. An external resistor is used
to set the required current for each level.
Compared to the linear current control technique,
this method allows designers to achieve the best
and most efficient performance possible with the
selected current, thereby avoiding linear element
The Shutdown (SHDN) pin saves power when the
camera flash is not used by consuming less than
0.1µA of current. When the SHDN pin is high
(logic '1'), the device is turned OFF and there is no
DC current path from the supply to the white LEDs
(Load Disconnect). If it is held to GND, the output
current continuously flows through the LEDs
(Torch mode). The SHDN pin, when it is set to low
(logic '0'), is also used to set the flash function
time duration.
DFN10L (3x3)
Order Codes
DFN10L (3mm x 3mm)
4500 parts per reel

Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16 

Fiches technique Télécharger

Go To PDF Page

Lien URL

Politique de confidentialité
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©

Mirror Sites
English :  |   English :  |   Chinese :  |   German :  |   Japanese :
Russian :  |   Korean :  |   Spanish :  |   French :  |   Italian :
Portuguese :  |   Polish :  |   Vietnamese :