ADC10040CIMT datasheet(8/19 Pages) NSC

No de pièce	ADC10040CIMT

Description	10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter

Download	19 Pages

Scroll/Zoom	100%

Fabricant	NSC [National Semiconductor (TI)]

Site Internet	http://www.national.com

Logo

8 / 19 page

Specification Definitions

APERTURE DELAY is the time after the rising edge of the

clock to when the input signal is acquired or held for conver-

sion.

APERTURE JITTER (APERTURE UNCERTAINTY) is the

variation in aperture delay from sample to sample. Aperture

jitter manifests itself as noise in the output.

COMMON MODE VOLTAGE (V

CM)

is the d.c. potential

present at both signal inputs to the ADC.

CONVERSION LATENCY See PIPELINE DELAY.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of

the maximum deviation from the ideal step size of 1 LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital

waveform is high to the total time of one period. The speci-

fication here refers to the ADC clock input signal.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE

BITS) is another method of specifying Signal-to-Noise and

Distortion or SINAD. ENOB is defined as (SINAD - 1.76) /

6.02 and states that the converter is equivalent to a perfect

ADC of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency

at which the reconstructed output fundamental drops 3 dB

below its low frequency value for a full scale input.

GAIN ERROR is the deviation from the ideal slope of the

transfer function. It can be calculated as:

Gain Error = Positive Full-Scale Error − Negative Full-

Scale Error

INTEGRAL NON LINEARITY (INL) is a measure of the

deviation of each individual code from a line drawn from

negative full scale (1⁄2 LSB below the first code transition)

through positive full scale (1⁄2 LSB above the last code

transition). The deviation of any given code from this straight

line is measured from the center of that code value.

MISSING CODES are those output codes that will never

appear at the ADC outputs. The ADC10040 is guaranteed

not to have any missing codes.

NEGATIVE FULL SCALE ERROR is the difference between

the input voltage (V

IN+ −VIN−) just causing a transition from

negative full scale to the first code and its ideal value of

0.5 LSB.

OFFSET ERROR is the input voltage that will cause a tran-

sition from a code of 01 1111 1111 to a code of 10 0000 0000.

OUTPUT DELAY is the time delay after the rising edge of

the clock before the data update is presented at the output

pins.

PIPELINE DELAY (LATENCY) is the number of clock cycles

between initiation of conversion and when that data is pre-

sented to the output driver stage. Data for any given sample

is available at the output pins the Pipeline Delay plus the

Output Delay after the sample is taken. New data is available

at every clock cycle, but the data lags the conversion by the

pipeline delay.

POSITIVE FULL SCALE ERROR is the difference between

the actual last code transition and its ideal value of 11⁄2 LSB

below positive full scale.

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in

dB, of the rms value of the input signal to the rms value of the

sum of all other spectral components below one-half the

sampling frequency, not including harmonics or dc.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD)

Is the ratio, expressed in dB, of the rms value of the input

signal to the rms value of all of the other spectral compo-

nents below half the clock frequency, including harmonics

but excluding dc.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-

ence, expressed in dB, between the rms values of the input

signal and the peak spurious signal, where a spurious signal

is any signal present in the output spectrum that is not

present at the input.

TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-

pressed in dBc, of the rms total of the first six harmonic

levels at the output to the level of the fundamental at the

output. THD is calculated as:

where f

1 is the RMS power of the fundamental (output)

frequency and f

2 through f6 are the RMS power in the first 6

harmonic frequencies.

SECOND HARMONIC DISTORTION (2ND HARM) is the

difference expressed in dB, between the RMS power in the

input frequency at the output and the power in its 2nd

harmonic level at the output.

THIRD HARMONIC DISTORTION (3RD HARM) is the dif-

ference, expressed in dB, between the RMS power in the

input frequency at the output and the power in its 3rd har-

monic level at the output.

www.national.com

8

Numéro de pièce similaire - ADC10040CIMT

Fabricant	No de pièce	Fiches technique	Description
Texas Instruments	ADC10040CIMT	1Mb / 28P	[Old version datasheet] ADC10040/ADC10040Q 10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter
	ADC10040CIMT/NOPB	1Mb / 27P	[Old version datasheet] 55.5 mW A/D Converter
	ADC10040CIMTX	1Mb / 28P	[Old version datasheet] ADC10040/ADC10040Q 10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter
	ADC10040CIMTX/NOPB	1Mb / 27P	[Old version datasheet] 55.5 mW A/D Converter

More results

Description similaire - ADC10040CIMT

Fabricant	No de pièce	Fiches technique	Description
Texas Instruments	ADC10040	1Mb / 28P	[Old version datasheet] ADC10040/ADC10040Q 10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter
Fairchild Semiconductor	SPT7861	87Kb / 11P	10-BIT, 40 MSPS, 160 mW A/D CONVERTER
Cadeka Microcircuits LL...	SPT7863	183Kb / 11P	10-BIT, 40 MSPS, 160 mW A/D CONVERTER
National Semiconductor ...	ADC10080	927Kb / 19P	10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter
Texas Instruments	ADC10080	1Mb / 24P	[Old version datasheet] 10-Bit, 80 MSPS, 3V, 78.6 mW A/D Converter
Cadeka Microcircuits LL...	SPT7860	193Kb / 12P	10-BIT, 40 MSPS, 175 mW A/D CONVERTER
Cadeka Microcircuits LL...	SPT7861	180Kb / 11P	10-BIT, 40 MSPS, 160 mW A/D CONVERTER
Fairchild Semiconductor	SPT7860	99Kb / 12P	10-BIT, 40 MSPS, 175 mW A/D CONVERTER
Fairchild Semiconductor	SPT7863	91Kb / 11P	10-BIT, 40 MSPS, 160 mW A/D CONVERTER
Texas Instruments	ADC10040	1Mb / 27P	[Old version datasheet] 55.5 mW A/D Converter

More results

ADC10040CIMT Fiches technique(PDF) 8 Page - National Semiconductor (TI)

ADC10040CIMT Fiches technique(HTML) 8 Page - National Semiconductor (TI)

Numéro de pièce similaire - ADC10040CIMT

Description similaire - ADC10040CIMT

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Fiches technique Télécharger

Lien URL