Moteur de recherche de fiches techniques de composants électroniques
  French  ▼
ALLDATASHEET.FR

X  

TPS40070PWPG4 Fiches technique(PDF) 5 Page - Texas Instruments

Click here to check the latest version.
No de pièce TPS40070PWPG4
Description  HIGH-EFFICIENCY MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
Download  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  TI [Texas Instruments]
Site Internet  http://www.ti.com
Logo TI - Texas Instruments

TPS40070PWPG4 Fiches technique(HTML) 5 Page - Texas Instruments

  TPS40070PWPG4 Datasheet HTML 1Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 2Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 3Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 4Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 5Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 6Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 7Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 8Page - Texas Instruments TPS40070PWPG4 Datasheet HTML 9Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 30 page
background image
THERMAL
PAD
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
KFF
RT
LVBP
PGD
SGND
SS
FB
COMP
ILIM
VDD
BOOST
HDRV
SW
DBP
LDRV
PGND
PWP PACKAGE(1)(2)
(TOP VIEW)
TPS40070
TPS40071
www.ti.com .................................................................................................................................................. SLUS582J – DECEMBER 2003 – REVISED APRIL 2009
(1)
For more information on the PWP package, refer to TI Technical Brief (SLMA002).
(2)
PowerPAD™ heat slug must be connected to SGND (pin 5) or electrically isolated from all other pins.
Table 1. Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
Gate drive voltage for the high-side N-channel MOSFET. The BOOST voltage is 8 V greater than the input
BOOST
14
I
voltage. A capacitor should be connected from this pin to the SW pin.
Output of the error amplifier, input to the PWM comparator. A feedback network is connected from this pin to the
COMP
8
O
FB pin to compensate the overall loop. The comp pin is internally clamped to 3.4 V.
8-V reference used for the gate drive of the N-channel synchronous rectifier. This pin should be bypassed to
DBP
11
O
ground with a 1.0-
µF ceramic capacitor.
Inverting input to the error amplifier. In normal operation the voltage on this pin is equal to the internal reference
FB
7
I
voltage, 0.7 V.
Floating gate drive for the high-side N-channel MOSFET. This pin switches from BOOST (MOSFET on) to SW
HDRV
13
O
(MOSFET off).
Short circuit protection programming pin. This pin is used to set the overcurrent threshold. An internal current sink
from this pin to ground sets a voltage drop across an external resistor connected from this pin to VDD. The voltage
on this pin is compared to the voltage drop (VVDD -VSW) across the high side N-channel MOSFET during
ILIM
16
I
conduction. Just prior to the beginning of a switching cycle this pin is pulled to approximately VDD/2 and released
when SW is within 2 V of VDD or after a timeout (the precondition time) - whichever occurs first. Placing a
capacitor across the resistor from ILIM to VDD allows the ILIM threshold to decrease during the switch on time,
effectively programming the ILIM blanking time. See applications information.
A resistor is connected from this pin to VIN programs the amount of feed-forward voltage. The current fed into this
KFF
1
I
pin is internally divided by 25 and used to control the slope of the PWM ramp and program undervoltage lockout.
Nominal voltage at this pin is maintained at 400 mV.
Gate drive for the N-channel synchronous rectifier. This pin switches from DBP (MOSFET on) to ground (MOSFET
LDRV
10
O
off). For proper operation, the total gate charge of the MOSFET connected to LDRV should be less than 50nC.
4.2-V reference used for internal device logic only. This pin should be bypassed by a 0.1-
µF ceramic capacitor.
LVBP
3
O
External loads less than 1 mA and electrically quiet may be applied.
This is an open drain output that pulls to ground when soft start is active, or when the FB pin is outside a 10%
PGD
4
O
band around VREF.
Power ground reference for the device. There should be a low-impedance path from this pin to the source(s) of the
PGND
9
lower MOSFET(s).
RT
2
I
A resistor is connected from this pin to ground to set the internal oscillator and switching frequency.
SGND
5
Signal ground reference for the device.
Soft-start programming pin. A capacitor connected from this pin to ground programs the soft-start time. The
capacitor is charged with an internal current source of 10
µA. The resulting voltage ramp on the SS pin is used as
a second non-inverting input to the error amplifier. The voltage at this error amplifier input is approximately 1 V
SS
6
I
less that that on the SS pin. Output voltage regulation is controlled by the SS voltage ramp until the voltage on the
SS pin reaches the internal reference voltage of 1 V plus the internal reference voltage of 0.7 V. If SS is below the
1-V offset voltage to the error amplifier. The resulting output voltage is zero. Also provides timing for fault recovery
attempts. Maximum recommended capacitor value is 22nF.
This pin is connected to the switched node of the converter. It is used for short circuit sensing, gate drive timing
SW
12
I
information and is the return for the high side driver. A 1.5-
Ω resistor is required in series with this pin for
protection against substrate current issues.
VDD
15
I
Supply voltage for the device.
Copyright © 2003–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS40070 TPS40071


Numéro de pièce similaire - TPS40070PWPG4

FabricantNo de pièceFiches techniqueDescription
logo
Texas Instruments
TPS40070PWP TI-TPS40070PWP Datasheet
288Kb / 10P
[Old version datasheet]   HIGH-EFFICIANCY MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
More results

Description similaire - TPS40070PWPG4

FabricantNo de pièceFiches techniqueDescription
logo
Texas Instruments
TPS40077 TI-TPS40077_15 Datasheet
1Mb / 45P
[Old version datasheet]   HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40077 TI-TPS40077 Datasheet
677Kb / 42P
[Old version datasheet]   HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40077 TI-TPS40077_07 Datasheet
894Kb / 43P
[Old version datasheet]   HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40075 TI1-TPS40075_14 Datasheet
1Mb / 44P
[Old version datasheet]   MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40074 TI-TPS40074 Datasheet
529Kb / 38P
[Old version datasheet]   MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40074 TI1-TPS40074_16 Datasheet
454Kb / 38P
[Old version datasheet]   MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40075 TI-TPS40075 Datasheet
809Kb / 44P
[Old version datasheet]   MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40074 TI-TPS40074_15 Datasheet
999Kb / 42P
[Old version datasheet]   MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40070 TI-TPS40070 Datasheet
288Kb / 10P
[Old version datasheet]   HIGH-EFFICIANCY MIDRANGE INPUT SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40007-DIE TI1-TPS40007-DIE Datasheet
96Kb / 6P
[Old version datasheet]   LOW-INPUT, HIGH EFFICIENCY SYNCHRONOUS BUCK CONTROLLER
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


Fiches technique Télécharger

Go To PDF Page


Lien URL




Politique de confidentialité
ALLDATASHEET.FR
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com