Moteur de recherche de fiches techniques de composants électroniques |
|
TCA9517 Fiches technique(PDF) 9 Page - Texas Instruments |
|
|
TCA9517 Fiches technique(HTML) 9 Page - Texas Instruments |
9 / 18 page BUS B TCA9517 SDA SDAB SDA SCL SCLB SCL EN BUS A 3.3 V SDAA SCLA V CCA V CCB 10 kW 1.2 V SLAVE 400 kHz BUS MASTER 400 kHz 10 kW 10 kW 10 kW TCA9517 www.ti.com SCPS242 – DECEMBER 2012 APPLICATION INFORMATION A typical application is shown in Figure 6. In this example, the system master is running on a 3.3-V I2C bus, and the slave is connected to a 1.2-V bus. Both buses run at 400 kHz. Master devices can be placed on either bus. The TCA9517 is 5-V tolerant, so it does not require any additional circuitry to translate between 0.9-V to 5.5-V bus voltages and 2.7-V to 5.5-V bus voltages. When the A side of the TCA9517 is pulled low by a driver on the I2C bus, a comparator detects the falling edge when it goes below 0.3 VCCA and causes the internal driver on the B side to turn on, causing the B side to pull down to about 0.5 V. When the B side of the TCA9517 falls, first a CMOS hysteresis-type input detects the falling edge and causes the internal driver on the A side to turn on and pull the A-side pin down to ground. In order to illustrate what would be seen in a typical application, refer to Figure 8 and Figure 9. If the bus master in Figure 6 were to write to the slave through the TCA9517, waveforms shown in Figure 8 would be observed on the A bus. This looks like a normal I2C transmission, except that the high level may be as low as 0.9 V, and the turn on and turn off of the acknowledge signals are slightly delayed. On the B-side bus of the TCA9517, the clock and data lines would have a positive offset from ground equal to the VOL of the TCA9517. After the eighth clock pulse, the data line is pulled to the VOL of the slave device, which is very close to ground in this example. At the end of the acknowledge, the level rises only to the low level set by the driver in the TCA9517 for a short delay, while the A-bus side rises above 0.3 VCCA and then continues high. Figure 6. Typical Application VILC AND PULL-UP RESISTOR SIZING For the TCA9517 to function correctly, all devices on the B-side must be able to pull the B-side below the voltage input low contention level (VILC). This means that the VOL of any device on the B-side must be below 0.4V. VOL of a device can be adjusted by changing the IOL through the device which is set by the pull-up resistance value. The pull-up resistance on the B-side must be carefully selected to ensure that logic levels will be transferred correctly to the A-side. Copyright © 2012, Texas Instruments Incorporated Submit Documentation Feedback 9 Product Folder Links: TCA9517 |
Numéro de pièce similaire - TCA9517 |
|
Description similaire - TCA9517 |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |