Moteur de recherche de fiches techniques de composants électroniques
  French  ▼
ALLDATASHEET.FR

X  

AD544LH Fiches technique(PDF) 8 Page - Analog Devices

No de pièce AD544LH
Description  High Performance, BiFET Operational Amplifiers
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricant  AD [Analog Devices]
Site Internet  http://www.analog.com
Logo AD - Analog Devices

AD544LH Fiches technique(HTML) 8 Page - Analog Devices

Back Button AD544LH Datasheet HTML 4Page - Analog Devices AD544LH Datasheet HTML 5Page - Analog Devices AD544LH Datasheet HTML 6Page - Analog Devices AD544LH Datasheet HTML 7Page - Analog Devices AD544LH Datasheet HTML 8Page - Analog Devices AD544LH Datasheet HTML 9Page - Analog Devices AD544LH Datasheet HTML 10Page - Analog Devices AD544LH Datasheet HTML 11Page - Analog Devices AD544LH Datasheet HTML 12Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 8 / 12 page
background image
AD542/AD544/AD547
REV. B
–8–
current-to-voltage converting amplifier. This possibility necessi-
tates some form of input protection. Many electrometer type
devices, especially CMOS designs, can require elaborate Zener
protection schemes which often compromise overall perfor-
mance. The BiFET series requires input protection only if the
source is not current-limited, and as such is similar to many
JFET-input designs. The failure mode would be overheating
from excess current rather than voltage breakdown. If the
source is not current-limited, all that is required is a resistor in
series with the affected input terminal so that the maximum
overload current is 1.0 mA (for example, 100 k
Ω for a 100 volt
overload). This simple scheme will cause no significant reduc-
tion in performance and give complete overload protection. Fig-
ure 30 shows proper connections.
Figure 30. Input Protection
D/A CONVERTER APPLICATIONS
The BiFET series of operational amplifiers can be used with
CMOS DACs to perform both 2-quadrant and 4-quadrant
operation. The output impedance of a CMOS DAC varies with
the digital word, thus changing the noise gain of the amplifier
circuit. The effect will cause a nonlinearity the magnitude of
which is dependent on the offset voltage of the amplifier. The
BiFET series with trimmed offset will minimize this effect. Ad-
ditionally, the Schottky protection diodes recommended for use
with many older CMOS DACs are not required when using one
of the BiFET series amplifiers.
Figure 31a shows the AD547 and AD7541 configured for uni-
polar binary (2-quadrant multiplication) operation. With a dc
reference voltage or current (positive or negative polarity) ap-
plied at pin 17, the circuit operates as a unipolar converter.
With an ac reference voltage or current, the circuit provides
2-quadrant multiplication (digitally controlled attenuation).
Figure 31a. AD547 Used as DAC Output Amplifier
BiFET Application Hints
APPLICATION NOTES
The BiFET series was designed for high performance op amp
applications that require true dc precision. To capitalize on all
of the performance available from the BiFETs there are some
practical error sources that should be considered.
The bias currents of JFET input amplifiers double with every
10
°C increase in chip temperature. Therefore, minimizing the
junction temperature of the chip will result in extending the
performance limits of the device.
1. Heat dissipation due to power consumption is the main
contributor to self-heating and can be minimized by reducing
the power supplies to the lowest level allowed by the
application.
2. The effects of output loading should be carefully considered.
Greater power dissipation increases bias currents and de-
creases open loop gain.
GUARDING
The low input bias current (25 pA) and low noise characteristics
of the high performance BiFET op amp make it suitable for
electrometer applications such as photo diode preamplifiers and
picoampere current-to-voltage converters. The use of guarding
techniques in printed circuit board layout and construction is
critical for achieving the ultimate in low leakage performance
available from these amplifiers. The input guarding scheme
shown in Figure 29 will minimize leakage as much as possible;
the guard ring is connected to a low impedance potential at the
same level as the inputs. High impedance signal lines should not
be extended for any unnecessary length on a printed circuit.
Figure 29. Board Layout for Guarding Inputs
INPUT PROTECTION
The BiFET series is guaranteed for a maximum safe input
potential equal to the power supply potential. The input stage
design also allows differential input voltages of up to
±1 volt
while maintaining the full differential input resistance of 10
12
Ω.
This makes the BiFET series suitable for comparator situations
employing a direct connection to high impedance source.
Many instrumentation situations, such as flame detectors in gas
chromatographs, involve measurement of low level currents
from high-voltage sources. In such applications, a sensor fault
condition may apply a very high potential to the input of the


Numéro de pièce similaire - AD544LH

FabricantNo de pièceFiches techniqueDescription
logo
Analog Devices
AD5440 AD-AD5440 Datasheet
860Kb / 32P
   Dual 8-,10-,12-Bit High Bandwidth Multiplying DACs with Serial Interface
REV. 0
AD5440 AD-AD5440 Datasheet
717Kb / 32P
   Dual 8-/10-/12-Bit, High Bandwidth, Multiplying DACs with Parallel Interface
REV. C
AD5440 AD-AD5440 Datasheet
584Kb / 20P
   8-Bit, High Speed, Multiplying D/A Converter (Universal Digital Logic Interface)
REV. C
AD5440 AD-AD5440 Datasheet
753Kb / 25P
   Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Parallel Interface
REV. B
AD5440 AD-AD5440 Datasheet
405Kb / 20P
   Dual-Current Output, Parallel Input, 16 /14-Bit Multiplying DACs with 4-Quadrant Resistors
Rev. D
More results

Description similaire - AD544LH

FabricantNo de pièceFiches techniqueDescription
logo
Analog Devices
AD544 AD-AD544_15 Datasheet
382Kb / 12P
   High Performance, BiFET Operational Amplifiers
REV. B
AD547 AD-AD547_15 Datasheet
382Kb / 12P
   High Performance, BiFET Operational Amplifiers
REV. B
AD542 AD-AD542_15 Datasheet
382Kb / 12P
   High Performance, BiFET Operational Amplifiers
REV. B
logo
Motorola, Inc
MC1748 MOTOROLA-MC1748 Datasheet
842Kb / 4P
   HIGH PERFORMANCE OPERATIONAL AMPLIFIERS
logo
Texas Instruments
LM107 TI-LM107 Datasheet
54Kb / 4P
[Old version datasheet]   HIGH-PERFORMANCE OPERATIONAL AMPLIFIERS
logo
ON Semiconductor
MC33272A ONSEMI-MC33272A Datasheet
287Kb / 12P
   HIGH PERFORMANCE OPERATIONAL AMPLIFIERS
1996 REV 0
MC33282 ONSEMI-MC33282 Datasheet
248Kb / 12P
   HIGH PERFORMANCE OPERATIONAL AMPLIFIERS
REV 0
logo
Sanyo Semicon Device
LA6462M SANYO-LA6462M Datasheet
107Kb / 5P
   High-Performance Dual Operational Amplifiers
logo
STMicroelectronics
LS404 STMICROELECTRONICS-LS404 Datasheet
209Kb / 12P
   HIGH PERFORMANCE QUAD OPERATIONAL AMPLIFIERS
December 1997
logo
Sanyo Semicon Device
LA6358N SANYO-LA6358N_10 Datasheet
164Kb / 7P
   High-Performance Dual Operational Amplifiers
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Fiches technique Télécharger

Go To PDF Page


Lien URL




Politique de confidentialité
ALLDATASHEET.FR
ALLDATASHEET vous a-t-il été utile ?  [ DONATE ] 

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Echange de liens   |   Fabricants
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com