Moteur de recherche de fiches techniques de composants électroniques |
|
TC1044SMJA Fiches technique(PDF) 6 Page - TelCom Semiconductor, Inc |
|
TC1044SMJA Fiches technique(HTML) 6 Page - TelCom Semiconductor, Inc |
6 / 8 page 4-48 TELCOM SEMICONDUCTOR, INC. Figure 8. Positive Voltage Multiplier Combined Negative Voltage Conversion and Positive Supply Multiplication Figure 9 combines the functions shown in Figures 3 and 8 to provide negative voltage conversion and positive volt- age multiplication simultaneously. This approach would be, for example, suitable for generating +9V and –5V from an existing +5V supply. In this instance, capacitors C1 and C3 perform the pump and reservoir functions, respectively, for the generation of the negative voltage, while capacitors C2 and C4 are pump and reservoir, respectively, for the multi- plied positive voltage. There is a penalty in this configuration which combines both functions, however, in that the source impedances of the generated supplies will be somewhat higher due to the finite impedance of the common charge pump driver at pin 2 of the device. Efficient Positive Voltage Multiplication/Conversion Since the switches that allow the charge pumping op- eration are bidirectional, the charge transfer can be per- formed backwards as easily as forwards. Figure 10 shows a TC1044S transforming –5V to +5V (or +5V to +10V, etc.). The only problem here is that the internal clock and switch- drive section will not operate until some positive voltage has been generated. An initial inefficient pump, as shown in Figure 7. Lowering Oscillator Frequency 1 2 3 4 8 7 6 5 + V + VOUT C1 COSC + C2 TC1044S Figure 9, could be used to start this circuit up, after which it will bypass the other (D1 and D2 in Figure 9 would never turn on), or else the diode and resistor shown dotted in Figure 10 can be used to "force" the internal regulator on. Voltage Splitting The same bidirectional characteristics used in Figure 10 can also be used to split a higher supply in half, as shown in Figure 11. The combined load will be evenly shared be- tween the two sides. Once again, a high value resistor to the LV pin ensures start-up. Because the switches share the load in parallel, the output impedance is much lower than in the standard circuits, and higher currents can be drawn from the device. By using this circuit, and then the circuit of Figure 5, +15V can be converted (via +7.5V and –7.5V) to a nominal –15V, though with rather high series resistance (~250 Ω). 1 2 3 4 8 7 6 5 V+ VOUT = (2 V+) – (2 VF) + C2 D1 D2 + C1 TC1044S 1 2 3 4 8 7 6 5 + V + VOUT = (2 V +) – (2 VF) C1 D1 + + C3 C4 VOUT = –V + C2 TC1044S D2 + Figure 9. Combined Negative Converter and Positive Multiplier Negative Voltage Generation for Display ADCs The TC7106 is designed to work from a 9V battery. With a fixed power supply system, the TC7106 will perform conversions with input signal referenced to power supply ground. Negative Supply Generation for 4 ¹⁄₂ Digit Data Acquisition System The TC7135 is a 4 ¹⁄₂ digit ADC operating from ±5V supplies. The TC1044S provides an inexpensive –5V source. (See AN16 and AN17 for TC7135 interface details and software routines.) TC1044S CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER |
Numéro de pièce similaire - TC1044SMJA |
|
Description similaire - TC1044SMJA |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |