Moteur de recherche de fiches techniques de composants électroniques |
|
ISL54221IRUZ-T Fiches technique(PDF) 3 Page - Intersil Corporation |
|
ISL54221IRUZ-T Fiches technique(HTML) 3 Page - Intersil Corporation |
3 / 13 page 3 FN6820.0 December 16, 2008 Absolute Maximum Ratings Thermal Information VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.5V Input Voltages HSD2x, HSD1x (Note 2). . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V SEL, OE (Note 2) . . . . . . . . . . . . . . . . . . . . -0.3 to ((VDD) + 0.3V) Output Voltages D+, D- (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V Continuous Current (HSD2x, HSD1x) . . . . . . . . . . . . . . . . . . ±40mA Peak Current (HSD2x, HSD1x) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV Thermal Resistance (Typical, Note 3) θJA (°C/W) 10 Ld µTQFN Package . . . . . . . . . . . . . . . . . . . . . . 155 Maximum Junction Temperature (Plastic Package). . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Logic Control Input Voltage . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 2. Signals on HSD1x, HSD2x, D+,D- exceeding GND by specified amount are clamped. Signals on OE and SEL exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings. 3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 2.7V to 5.5V Supply Test Conditions: VDD = +3.3V, GND = 0V, VSELH = 1.4V, VSELL = 0.5V, VOEH = 1.4V, VOEL = 0.5V, (Note 4), Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP (°C) MIN (Notes 5, 6) TYP MAX (Notes 5, 6) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG VDD = VDD, SEL = 0V or VDD, OE = 0V Full 0 - VDD V ON-Resistance, rON (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV (see Figure 3, Note 9) 25 - 6.7 8 Ω Full - - 10 Ω rON Matching Between Channels, ΔrON (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, V VHSD1x or VHSD2 x = Voltage at max rON, (Notes 8, 9) 25 - 0.117 0.45 Ω Full - - 0.55 Ω rON Flatness, RFLAT(ON) (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV, (Notes 7, 9) 25 - 0.94 1.2 Ω Full - - 1.3 Ω OFF Leakage Current, IHSD1x(OFF) VDD = 5.5V, SEL = VDD and OE = 0V or OE = VDD, VDx = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V, VHSD2x = 0.3V, 3.3V 25 -15 0.31 15 nA Full -20 - 20 nA ON Leakage Current, IHSD1x(ON) VDD = 5.5V, SEL = OE = 0V, VDx = 0.3V, 3.3V, VHSD1X = 0.3V, 3.3V, VHSD2x = 3.3V, 0.3V 25 -20 2.2 20 nA Full -25 - 25 nA OFF Leakage Current, IHSD2x(OFF) VDD = 5.5V, SEL = OE = 0V or OE = VDD, VDx = 3.3V, 0.3V, VHSD2x = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V 25 -15 0.26 15 nA Full -20 - 20 nA ON Leakage Current, IHSD2x(ON) VDD = 5.5V, SEL = VDD, OE = 0V, VDx= 0.3V, 3.3V, VHSD2x = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V 25 -20 2.1 20 nA Full -25 - 25 nA Power OFF Leakage Current, ID+, ID- VDD = 0V, VD+ = 0V to 5.25V, VD-= 0V to 5.25V, SEL = OE = VDD 25 - 0.0047 0.025 µA Full - - 0.40 µA DYNAMIC CHARACTERISTICS Turn-ON Time, tON VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 1) 25 - 35 - ns Turn-OFF Time, tOFF VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 1) 25 - 27 - ns Break-Before-Make Time Delay, tD VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 2) 25 - 10 - ns ISL54221 |
Numéro de pièce similaire - ISL54221IRUZ-T |
|
Description similaire - ISL54221IRUZ-T |
|
|
Lien URL |
Politique de confidentialité |
ALLDATASHEET.FR |
ALLDATASHEET vous a-t-il été utile ? [ DONATE ] |
À propos de Alldatasheet | Publicité | Contactez-nous | Politique de confidentialité | Echange de liens | Fabricants All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |