TDA7433D datasheet(8/10 Pages) STMICROELECTRONICS

No de pièce	TDA7433D

Description	BASIC FUNCTION AUDIO PROCESSOR

Download	10 Pages

Scroll/Zoom	100%

Fabricant	STMICROELECTRONICS [STMicroelectronics]

Site Internet	http://www.st.com

Logo

8 / 10 page

Functional Description

The input selector is able to select 2 stereo inputs

and 1 mono input (AM). The inputs are DC biased

with 100k

Ω resistors to the internal reference volt-

age of 3V. The mono input can be used addition-

ally as hardware mute pin. If this pin is pulled to

ground by an external transistor and AM is not se-

lected, the input selector mutes the input (refer-

ence voltage selected). The AM part is consid-

ered to be switched OFF. If the output of the AM

part is not high ohmic in this condition, a series

resistor of about 20k

Ω has to be foreseen.

The volume control can be programmed from a

gain of +32dB to an attenuation of -79dB in 1dB

steps. The maximum gain should be kept as low

as possible for system performance reason. It has

to be limited by software to the absolute neces-

sary system gain, depending on the signal source

level and the power amplifier gain.

The bass control acts in a range from +18dB to -

18dB in 2dB steps. The filter response is deter-

mined by the external filter components. An ex-

tensive simulation software is available in order to

support the design of the bass filter response with

different filter configurations.

The extended bass boost range of +18dB allows

the implementation of the software loudness func-

tion by additional bass and treble boost.

The treble control acts in a range of

±14dB in 2dB

steps. The external capacitor determines with the

internal resistor of 50K

Ω the corner frequency of

the treble response.

The four speaker attenuators can be controlled in-

dependently from 0 to -37.5dB, which allows the

implementation of balance and fader a the four

speaker system. The attenuation steps size is 1

db from 0 to -24dB and increases non linearly up

to the maximum attenuation of 37.5dB. A special

mute bit forces the speaker attenuator into the

mute position.

All 4 outputs are low distortion push pull outputs,

able to drive a load of 3k

Ω.

TDA7433

8/10

Numéro de pièce similaire - TDA7433D

Fabricant	No de pièce	Fiches technique	Description
STMicroelectronics	TDA7430	168Kb / 21P	DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SURROUND SOUND MATRIX AND VOICE CANCELLER September 1999
	TDA7430	231Kb / 23P	DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SURROUND SOUND MATRIX AND VOICE CANCELLER
	TDA7430TR	231Kb / 23P	DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SURROUND SOUND MATRIX AND VOICE CANCELLER
	TDA7430	231Kb / 23P	DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SURROUND SOUND MATRIX AND VOICE CANCELLER
	TDA7431	168Kb / 21P	DIGITALLY CONTROLLED AUDIO PROCESSOR WITH SURROUND SOUND MATRIX AND VOICE CANCELLER September 1999

More results

Description similaire - TDA7433D

Fabricant	No de pièce	Fiches technique	Description
STMicroelectronics	TDA7434	88Kb / 10P	BASIC FUNCTION AUDIO PROCESSOR August 1996
STMicroelectronics	TDA7432	87Kb / 10P	BASIC FUNCTION AUDIO PROCESSOR August 1996
Cirrus Logic	CS4811	354Kb / 24P	Fixed Function Multi-Effects Audio Processor
Cirrus Logic	CS4812	541Kb / 36P	Fixed Function Multi-Effects Audio Processor
STMicroelectronics	TDA7403	234Kb / 25P	BASIC SIGNAL PROCESSOR
STMicroelectronics	TDA7403	195Kb / 26P	BASIC SIGNAL PROCESSOR October 1998
New Japan Radio	NJW1143	160Kb / 17P	AUDIO PROCESSOR
	NJW1138	352Kb / 21P	AUDIO PROCESSOR
	NJW1141	287Kb / 20P	AUDIO PROCESSOR
	NJW1142	123Kb / 14P	AUDIO PROCESSOR

More results

TDA7433D Fiches technique(PDF) 8 Page - STMicroelectronics

TDA7433D Fiches technique(HTML) 8 Page - STMicroelectronics

Numéro de pièce similaire - TDA7433D

Description similaire - TDA7433D

Html Pages

1 2 3 4 5 6 7 8 9 10

Fiches technique Télécharger

Lien URL