Moteur de recherche de fiches techniques de composants électroniques
Selected language     French  ▼
Nom de la pièce
         Description


ADL5500 Datasheet(Fiches technique) 20 Page - Analog Devices

Numéro de pièce ADL5500
Description  100 MHz to 6 GHz TruPwr Detector
Télécharger  24 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fabricant  AD [Analog Devices]
Site Internet  http://www.analog.com
Logo 

 
 20 page
background image
ADL5500
Rev. A | Page 20 of 24
EVALUATION BOARD
Figure 48 shows the schematic of the ADL5500 evaluation
board. The layout and silkscreen of the evaluation board layers
are shown in Figure 49 to Figure 52. The board is powered by a
single supply in the 2.7 V to 5.5 V range. The power supply is
decoupled by 100 pF and 0.01 μF capacitors. Table 5 details the
various configuration options of the evaluation board.
Problems caused by impedance mismatch can arise using the
evaluation board to examine the ADL5500 performance. One
way to reduce these problems is to put a coaxial 3 dB attenuator
on the RFIN SMA connector. Mismatches at the source, cable,
and cable interconnection, as well as those occurring on the
evaluation board, can cause these problems.
A simple (and common) example of such a problem is triple
travel due to mismatch at both the source and the evaluation
board. Here the signal from the source reaches the evaluation
board and mismatch causes a reflection. When that reflection
reaches the source mismatch, it causes a new reflection, which
travels back to the evaluation board, adding to the original
signal incident at the board. The resultant voltage varies with
both cable length and frequency dependence on the relative
phase of the initial and reflected signals. Placing the 3 dB pad at
the input of the board improves the match at the board and thus
reduces the sensitivity to mismatches at the source. When such
precautions are taken, measurements are less sensitive to cable
length and other fixture issues. In an actual application when
the distance between ADL5500 and source is short and well-
defined, this 3 dB attenuator is not needed.
Land Pattern and Soldering Information
Figure 47 shows the land pattern used on the ADL5500
evaluation board. Pad diameters of 0.28 mm are used with a
solder paste mask opening of 0.38 mm. For the RF input trace, a
trace width of 0.30 mm is used, which corresponds to a 50 Ω
characteristic impedance for the dielectric material being used
(FR4). All traces going to the pads are tapered down to 0.15 mm.
For the RFIN line, the length of the tapered section is 0.20 mm.
0.28 mm
0.50 mm
0.15 mm
0.30 mm
(50
Ω)
0.15 mm
0.50 mm
0.38 mm
(PASTE MASK OPENING)
RFIN
VPOS
VRMS
COMM
0.20 mm
GROUND
PLANE
Figure 47. Land Pattern Used on the ADL5500 Evaluation Board
COMM
VRMS
RFIN
VPOS
2
4
3
1
ADL5500
C4
10nF
R8
(OPEN)
R6
(OPEN)
VRMS
RFIN
VPOS
C1
100pF
C2
0.1
μF
TO EDGE
CONNECTOR
R3
0
Ω
Figure 48. Evaluation Board Schematic
Table 5. Evaluation Board Configuration Options
Component
Description
Default Condition
VPOS, GND
Ground and Supply Vector Pins.
Not Applicable
C1, C2
Power Supply Decoupling. The nominal supply decoupling of 0.01 μF and 100 pF.
C1 = 0.01 μF (Size 0402)
C2 = 100 pF (Size 0402)
R3, R8, C4
Output Filtering. The combination of the internal 1 kΩ output resistance and C4 produce
a low-pass filter to reduce output ripple. The output can also be scaled down using the
resistor divider pads, R3 and R8. In addition, resistors and capacitors can be placed in C4 and
R8 to load test VRMS.
R3 = 0 Ω (Size 0402)
R8 = Open (Size 0402)
C4 = 10 nF (Size 0402)
R6
Alternate Interface. R6 allows VOUT to be accessible from the edge connector, which is only
used for characterization.
R6 = Open (Size 0402)




Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24 


Datasheet Download



Numéro de composants électroniques

Numéro de pièceDescription des composantsHtml ViewFabricant
ADL550150 MHz to 4 GHz TruPwr Detector 1 2 3 4 5 MoreAnalog Devices
AD8312100 MHz-2.7 GHz 45 dB RF Log Detector 1 2 3 4 5 MoreAnalog Devices
AD83181 MHz - 8 GHz 60 dB Logarithmic Detector/Controller 1 2 3 4 5 MoreAnalog Devices
CGY40GaAs MMIC Single-stage monolithic microwave IC MMICamplifier Application range: 100 MHz to 3 GHz 1 2 3 4 5 Siemens Semiconductor Group
MRF275G150 W 28 V 500 MHz N.CHANNEL MOS BROADBAND 100 - 500 MHz RF POWER FET 1 2 3 4 5 MoreMotorola, Inc
PCK2023CK408 66/100/133/200 MHz spread spectrum differential system clock generator 1 2 3 4 5 MoreNXP Semiconductors
AD8314100 MHz-2500 MHz 45 dB RF Detector/Controller 1 2 3 4 5 MoreAnalog Devices
EL2120C100 MHz Current Feedback Amplifier 1 2 3 4 5 MoreElantec Semiconductor
A36-1100 TO 2300 MHz CASCADABLE AMPLIFIER 1 Tyco Electronics
UF28150JPOWER MOSFET TRANSISTOR 150 WATTS 100 - 500 MHz 28 V 1 2 3 Tyco Electronics

Lien URL

AllDATASHEET vous a-t-il été utile ?   [ DONATE ]  

À propos de Alldatasheet   |   Publicité   |   Contactez-nous   |   Politique de confidentialité   |   Favoris   |   Echange de liens   |   Fabricants
All Rights Reserved © Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl